Modified on: Wed, 18 Dec, 2019 at 3:51 PM. The cartridge is integrated into the headshell for assured performance and ease of setup. This is to make certain the automatic mechanism is fully cycled. Rotate the platter by hand until the large rectangular opening with the red ribbon is positioned in the upper left corner of the turntable (the 10 o’clock position). Audio-Technica AT-LP60X Turntable Overview + Setup Guide - … Then plug the RCA end (red and white plugs) into your desired playback device (commonly a stereo receiver or powered speakers). Insert the two dust cover hinges on the rear of the turntable and then insert the dust cover onto the hinges. Did you find it helpful? Please note that if the belt is not placed properly on this turntable, the turntable may not seem like it is getting any power when the start button is pressed. Be careful not to damage the stylus. If connecting to any other input on a stereo receiver (Aux, Line, Tape, CD, etc.) Patrick is the author of this solution article. The entire setup process may be viewed in the following video. The AT-LP60X is also equipped with a detachable RCA output cable (3.5 mm male to dual RCA male), 45 RPM adapter, and a removable hinged dust cover. You should have: Die-cast aluminium platter with the drive belt attached to the bottom ring of the platter, Analog audio output cable (3.5 mm male to dual RCA male), Quick Start Guide (full owner’s manual available for download here). Place the platter on the turntable’s centre spindle, making sure the platter is fully seated. Help us improve this article with your feedback. Audio-Technica has been a leader in phono cartridge design for more than 50 years, and that expertise shows in the AT-LP60X’s Dual Magnet™ cartridge with replaceable stylus. No need for additional adapter cables. If connecting to inputs on a stereo receiver specifically labelled “PHONO,” move the switch on the rear of the turntable to PHONO. For a better listening experience, the turntable includes an AC adapter that moves the AC/DC conversion outside of the chassis where its impact on the signal chain is limited. Once the belt is properly installed on the motor pulley, you may remove and discard the red ribbon. AT-LP60X Setup | Fully Automatic Belt-Drive Turntable - YouTube This tutorial will guide you through the setup process for the Audio-Technica AT-LP60X Fully Automatic Belt-Drive Turntable.This affordable, easy-to-use turntable plays both 33-1/3 and 45 RPM records and, with its built-in switchable phono preamp, can be connected directly to your home stereo, powered speakers, computer and other components, whether they have a dedicated phono input or not. The provided dust cover is designed to protect the turntable when not in use and may be closed when records are playing. This engages the turntable’s internal RIAA magnetic phono preamp. While holding the platter steady, remove the tape holding the red ribbon to the platter, then use the ribbon to guide the drive belt (attached to the underside of the platter) over the brass motor pulley. Connect the power adapter cable to the turntable and plug the adapter into a convenient AC outlet. This is important to ensure that the turntable operates at the proper speed. How to set up an AT-LP60X turntable?Print Carefully remove the turntable from the packaging and verify that all of the parts and accessories are present. While holding the tonearm in the rest position, carefully remove the plastic stylus guard by slowly pulling the guard-forward. Place the slip mat on the platter and (with the tonearm still fastened to its rest) rotate the platter ten times in the clockwise direction. Also, verify that the belt is not twisted on the motor pulley. This will expose the brass-coloured motor pulley. Proper setup of the AT-LP60X will ensure that the turntable will perform to its full potential. If connecting the turntable to a 3.5 mm analogue AUX input on a speaker or receiver, you may use a 3.5 mm stereo AUX cable (not included). Remove the plastic tie that is securing the tonearm to its rest and discard the plastic tie. This bypasses the turntable’s internal RIAA magnetic phono preamp, which isn’t needed since the stereo receiver’s PHONO input has the same RIAA magnetic phono preamp. Audio-Technica AT-LP60X Turntable | Review Setup & Test - … If the switch is set to “Phono” you may have little or no sound at all. The AT-LP60X, a redesign of the popular AT-LP60 turntable, features an improved tonearm base and headshell to improve tracking and reduce resonance. If the switch is set to “Line” you may hear considerable amounts of distortion. (Note: make sure you are exposing the brass pulley and not the white plastic post at the 2 o’clock position.). Follow the steps below to properly set up the AT-LP60X turntable. No. Yes Learn more about the AT-LP60X Turntable: https://bit.ly/2YO9xOn Sorry we couldn't be helpful. Connect the analogue audio cable’s 3.5 mm plug into the “Analog Out” port on the back centre of the turntable. Make certain the belt is properly seated on the motor pulley so it is riding in the pulley’s groove. Carefully remove the turntable from the packaging and verify that all of the parts and accessories are present. or connecting directly to powered speakers, move the switch on the rear of the turntable to LINE.

Traditional Wedding Readings, My Chemical Romance The Black Parade Lyrics, Eas Simulator Pro Aptoide, Zoolander 2 Cast, Benefits Of Mutual Funds, Paranoia Drinking Game Questions, Omx Meaning, Wanda Group Ceo, John Thaw Funeral,